керівництво користувача PHILIPS 42PFL8404H

[. . . ] KG (SHC), die ihrerseits das Gigaset-Geschäft der Siemens AG fortführte. Etwaige Erklärungen der Siemens AG oder der SHC in den Bedienungsanleitungen sind daher als Erklärungen der Gigaset Communications GmbH zu verstehen. Wir wünschen Ihnen viel Freude mit Ihrem Gigaset. Chère Cliente, Cher Client, la société Gigaset Communications GmbH succède en droit à Siemens Home and Office Communication Devices GmbH & Co. [. . . ] To operate clients with older wireless network adapters in your network, select IEEE 802. 11b/g (mixed). ì Select the required transmission mode for your wireless network. Sending power ì Select the required sending power for your device. It is recommended that you select a sending power with a range to suit the spatial environment of your local network. A much greater range makes it easier to eavesdrop on your wireless data transfer. XR (extended range) By activating XR, wireless data transfer is also enabled in the border areas of your wireless network, though at a very slow data transfer rate. The switch to XR mode happens automatically if there is a weak signal and if the remote station is likewise XR-enabled. ì Activate or deactivate XR for your wireless network to increase the range. ì Click OK to apply the settings. 68 Configuring Advanced Settings WDS (repeater function) If you use a repeater to extend the range in your wireless network, you must activate the Wireless Distribution System (WDS) function. Security settings in the wireless network If you are sending data over radio channels, we recommend that you activate encryption (WEP or WPA) on the components in the wireless network. You should therefore select WPA encryption if it is supported by all components in your wireless network. WPA is a more efficient method than WEP for protecting wireless networks. Dynamic keys, based on TKIP (Temporal Key Integration Protocol) offer increased security. WPA also supports the use of an authentication server. ì In the Wireless Network menu, select Encryption & Authentication. The following security mechanisms are currently available: u WPA2-PSK and WPA2-PSK/WPA-PSK (page 70) u WAP2 and WPA2/WPA with authentication server (page 71) u WEP encryption (Wired Equivalent Privacy, see page 72) 69 Configuring Advanced Settings WPA2-PSK and WPA2-PSK / WPA-PSK WPA with pre-shared key (WPA-PSK) WPA-PSK is a special WPA mode for private users and users in small companies without their own authentication server. After a certain period of time (Rekey interval), encryption keys are automatically generated with the pre-shared key, automatically changed ("rekeying") and authenticated between the devices. The standard of encryption available to you depends on the components in the wireless network. Every PC (network adapter) that requires access to a WPA-protected wireless network must also support WPA. An example of a valid key: GIGASET_SX76x ì Enter up to four keys in fields Key 1 to Key 4 and confirm them by entering them again in fields Confirm key 1 to Confirm key 4. ì Select one of the four keys as the Default key. Note: u It is very important that you make a note of the key(s) that have been entered or generated. You will need this information to configure the wireless network adapters properly. u When you have concluded the configuration, you must change the WEP encryption in the wireless network adapters for the connected PCs in the same way as they will not otherwise be given access to the wireless network of the Gigaset SX762 WLAN dsl. ì Click OK to apply the settings. 73 Configuring Advanced Settings Generating a key by means of a Passphrase ì Enter a Passphrase (up to 32 characters) and confirm it by entering it again. The key is generated automatically. ì Click OK to apply the settings. Permitted clients On this screen you can specify the PCs that are to have wireless access to the Gigaset SX762 WLAN dsl and hence to your LAN and WLAN. In the Advanced Settings ­ Wireless Network menu, select Allowed Clients. The default setting for access control is deactivated. This means that all PCs that use the correct SSID can be logged in. Access control is based on the MAC addresss of the PC network adapters. ì Activate access control by selecting On in the MAC address filter field. 74 Configuring Advanced Settings Entering PCs manually: ì Enter the MAC address and Device name of the required PCs in the appropriate fields. ì Click the Add button to add the entry to the list. ì Click the Delete button to delete the entry from the list. Note: Only following deletion is the entry transferred to the list of known MAC addresses. ì Apply the settings by clicking OK. Selecting from the list of logged-in PCs ì Select the required PC from the Known wireless clients list. All PCs that were already entered manually on the router with the MAC address are displayed. ì Click the Add button to add the selected PC to the list. ì Apply the settings by clicking OK. Note: If you activate MAC access control, you must at least add the PC on which you are configuring the Gigaset SX762 WLAN dsl to the list. Otherwise, you will have no access to the user interface and will receive an appropriate error message. [. . . ] 17 Installing printer driver Windows XP/2000. 115 Institute of Electrical and Electronic Engineers, see IEEE Internet . 55 setting up multiple connection services . 5 Internet connection changing configuration. [. . . ]