керівництво користувача AEG-ELECTROLUX EHG3143X

[. . . ] Please contact your retailed before installing the appliance. The manufacturer declines any responsibility in case of not respecting the accident prevention rules. First of all consult the content of this handbook. If you do not find the information you need, please contact the closest Assistance Centre. The assistance to this appliance has to be carried out by the authorized Technical Assistance Centre. [. . . ] Before taking out the pans from the burner, turn the flame down or shut it off. During the cooking where greases of oils are used, look carefully at your cooking as these substances can cause fire if brought to an high temperature. 3 Cleaning and maintenance Before any intervention it is necessary to control the appliance is UNCONNECTED from the electricity supply. General cleaning Wash the enamelled parts with warm water and detergent, avoiding to use abrasive products which could scratch it. Wash often the crowns and the grid caps with boiling soapy water, pay attention to scrape every scale off. After the use rinse the stainless steel parts carefully using water, and dry them with a soft cloth. For persistent spots use normal non abrasive detergent easy commonly to be found in commerce. We recommend you not to use for the cleaning straw hats, steel wools or acids. Cleaning of the electrical ignition The automatic ignition of the burners is assured by the presence of a ceramic "glow plug" and by a metal longdistance line. Periodically proceed with an accurate cleaning of these parts of the hob. In order to avoid any difficulty in the ignition, control that the holes of the crown (letter B) are not clogged Picture 2 Hob's grids. Hobs can be equipped by stainless steel grids (see picture 2) or cast iron grids (bigger and heavy ­ see picture 3). The grids can be taken off to enable a better cleaning. Lift the grids up form the hob. Grids and chromium-plated grids caps. Grids and chromium-plated grids caps tend to darken with their use. This is an absolute regular and unavoidable phenomenon but it does not absolutely compromise the hob functionality. . By the way, upon request, there are enamelled grids and grids caps available by your retailer or our Technical Assistance Centres. Picture 3 Periodic maintenance. The condition of the gas-supply pipe should be checked periodically and, if present, the condition of the pressure control. If you find any irregularities do not ask to repair them but ask for their replacement. To grant the proper working and safety it is necessary to periodically grease the gas regulation cocks. The periodic lubrication of the gas cocks must be done by QUALIFIED PERSONNEL ONY whom has to be contacted in case of anomalies to the appliance working. 4 Assistance and spare parts. This appliance, before leaving the warehouse, has been tested and set by qualified personnel to obtain the best working performance. If any repairs are required, they have to be done with the maximum care and attention. For this reason we recommend you to contact the retailer who dealt with the sale or the closest Assistance Centre, specifying the type of inconvenience, the appliance model (Mod. ), the product number (Prod. These datum are indicated on the label on the last page og the handbook. Original spare parts, certified by the product manufacturer and countersigned by this brand, are available by our Technical Assistance Centres and Authorized Spare Parts Shops only. 5 Technical features Gas burners power Ultra-rapid treble crown burner (big) Rapid burner (big) Auxiliary burner (small) Semi-rapid burner (medium) 4, 0 Kw 3, 0 Kw 1, 0 kW 2, 0 kW Appliance Calibration Gas inlet connector Feeling tension Methane Gas 20 mbar G 1/2" 230 V 50 Hz Category II2E+3+ Dimensions for the recess opening Width Depth 472 mm 406 mm Instructions for the installer WARNING: This appliance can be installed and can work only in permanently well-ventilated rooms in accordance with o UNI 7129 e UNI 7131 regulations. The installation of the appliance and the connection to the electric network must be carried out exclusively by QUALIFIED PERSONNEL ONLY. Before doing any sort intervention it is important to verify the equipment is disconnected from the electrical network THE CONSTRUCTOR COMPANY DECLINES FROM ANY RESPONSABILITY IN CASE OF DEMAGES CAUSED BY AN INSTALLATION NOT IN COMPLIANCE WITH THE CURRENT REGULATIONS AND WITHOUT RESPECTING THE ACCIDENT PREVENTION RULES. [. . . ] 4. Picture 15 10 BY-PASS DIAMETRES Burner Ø By-pass tap in hundredth 28 32 40 56 Auxiliary Semi-rapid Rapid Ultra-rapid with treble crown BURNERS SPECIFICATIONS TYPE OF GAS TYPE OF BURNER NOZZLES MARKING 1/100 mm NOMINAL THERMIC RATE kW REDUCED TERMIC RATE kW NOMINAL IN RATE m3 /h g/h - NOMINAL PRESSURE mbar Ultra-rapid (big) NATURAL GAS (Methane) Rapid Semi-rapid (medium) Auxiliary (small) 146 119 96 70 4, 0 3, 0 2, 0 1, 0 1, 2 0, 65 0, 45 0, 33 0, 381 0, 305 0, 190 0, 095 20 Ultra-rapid (big) LIQUID GAS (Butane/ Propane) Rapid Semi-rapid (medium) Auxiliary (small) 98 86 71 50 4, 0 3, 0 2, 0 1, 0 1, 2 0, 65 0, 45 0, 33 - 288 202 28-30/37 144 72 11 Types of cooker tops Tops with stainless steel grids Tops with cast iron steel grids 12 Positioning and connection Cookers can be mounted on a furniture with a recess opening with dimensions shown in picture16 The fixing of the hob to the top has to be done as follows: Position the suitable dope, not issued, on the front, back and side edges of the worktop's opening (as shown in picture. Ad just the hob on the opening of the furniture paying attention to centre it. Fix the hob to the furniture using provided brackets (see picture 20). The traction of the screws is enough to trace the dope, whose excess could easily therefore be removed. [. . . ]